Beginner's Plumbing: The Essentials for Installing a Bathtub
Beginner's Plumbing: The Essentials for Installing a Bathtub
Blog Article
How do you feel on the subject of A Step-by-Step Guide to Installing a Bathtub?

Setting up a bathtub isn't specifically brain surgery, but it does require strong plumbing, carpentry, and in some cases, tiling skills. Changing an old bathtub with a brand-new one is also a moderately difficult job. If the old tub is easily accessible, the project can relocate rapidly; if you need to open a wall surface to eliminate the old bathtub and position the brand-new bath tub, the job is much harder. In either instance, the job is within a house handyman's abilities, although you will need a helper to leave the old bathtub as well as embeded in the new one. Make certain you have actually qualified yourself for the job and are comfortable attempting it. As opposed to hiring a contractor to take over a halfway-completed job, it is far better to think about utilizing one before you begin. Possibilities are you might need a specialist plumber to make tube connections.
This article will assist you mount a new bathtub in your shower room if you have currently gotten a brand-new bathtub and also don't require to change the arrangement of your previous water pipes.
Your devices and also material checklist need to comprise the following:
Preparing for the Setup
First of all, the supporting framework provided with the bathroom ought to be fitted (if required) according to the maker's guidelines. Next, fit the taps or mixer to the tub. When fitting the tap block, it is important to make sure that if the tap comes with a plastic washer, it is fitted between the bath and also the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps device to stop strain on the tub.
Fit the adaptable faucet ports to the bottom of the two faucets utilizing 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet via the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you utilize all of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom should currently prepare to be fitted in its final setting.
Removing Old Touches
If you require to replace old taps with new ones as a part of your installment, then the first thing you should do is disconnect the water system. After doing so, switch on the taps to drain pipes any type of water continuing to be in the system. The procedure of removing the existing taps can be fairly bothersome as a result of the limited accessibility that is commonly the case.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth ready for the staying water that will come from the pipelines. Once the supply pipelines have actually been removed, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from transforming during this procedure. When the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old securing substance.
Before going on to fit the brand-new faucets, contrast the pipe connections on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Setting up the Bath tub
Utilizing the two wooden boards under its feet, put the bathtub in the required setting. The wooden boards are useful in evenly spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 tiny points.
The following goal is to guarantee that the tub is leveled all round. This can be attained by checking the spirit level and also adjusting the feet on the bathtub until the spirit level reads level.
To mount taps, fit all-time low of the furthest flexible faucet port to the appropriate supply pipeline by making a compression join; then do the exact same for the various other faucet.
Switch on the water system as well as examine all joints as well as brand-new pipework for leaks as well as tighten them if needed. Fill the tub and likewise inspect the overflow electrical outlet and also the regular outlet for leakages.
Ultimately, repair the bathroom paneling as described in the supplier's instruction manual. Tiling and sealing around the bathtub needs to wait until the tub has been made use of at least once as this will settle it into its final setting.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to stop damage to the string. One end of the port fits on the plastic tail of the faucet as well as the various other end supplies a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will require minimizing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, position the faucet in the placing opening in the bath/basin guaranteeing that the washing machines are in place in between the tap and also the sink. Safeguard the tap in place with the maker supplied backnut. As soon as the tap is safely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with typical tap adapters. The previous type should be attached to the faucet finishes first, tightening only by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is needed to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate enough to split a rigid seal, triggering the water to permeate the wall surface between the bath and the tiling, resulting in problems with wetness and feasible leaks to the ceiling below.
You can choose from a selection of coloured sealants to assimilate your fixtures and installations. They are marketed in tubes and cartridges, and can securing voids as much as a width of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of drenched paper or soft rope. Bear in mind to always load the bathtub with water before securing, to allow for the motion experienced when the bathtub remains in use. The sealer can crack fairly early if you do not consider this activity prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally conveniently offered on the marketplace. It is recommended to fit the ceramic tiles using water-resistant or waterproof sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

Hopefully you enjoyed our article about Installing A Bathtub. Thanks a lot for taking a few minutes to read through our piece of content. So long as you enjoyed reading our blog posting if you please make sure you remember to pass it around. Thanks for taking the time to read it.
Pro assistance? Dial. Report this page